在没有互联网连接的情况下安装B43驱动程序

我整天都在尝试解决此问题，但没有结果。我正在使用elementaryOS Luna，但由于它可以在Ubuntu上运行...

我的问题是我的Dell Vostro 1500的以太网有问题。由于某种原因，它无法连接到以太网，很可能是硬件问题，因此我需要在安装驱动程序的计算机上没有安装互联网的情况下进行安装。

需要第二台装有Linux的计算机的解决方案将无法使用。这是从OS X键入的，我拥有的另一台计算机是有问题的计算机。

运行lspci我得到：

00:00.0 Host bridge: Intel Corporation Mobile PM965/GM965/GL960 Memory Controller Hub (rev 0c)
00:02.0 VGA compatible controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (primary) (rev 0c)
00:02.1 Display controller: Intel Corporation Mobile GM965/GL960 Integrated Graphics Controller (secondary) (rev 0c)
00:1a.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #4 (rev 02)
00:1a.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #5 (rev 02)
00:1a.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #2 (rev 02)
00:1b.0 Audio device: Intel Corporation 82801H (ICH8 Family) HD Audio Controller (rev 02)
00:1c.0 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 1 (rev 02)
00:1c.1 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 2 (rev 02)
00:1c.3 PCI bridge: Intel Corporation 82801H (ICH8 Family) PCI Express Port 4 (rev 02)
00:1d.0 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #1 (rev 02)
00:1d.1 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #2 (rev 02)
00:1d.2 USB controller: Intel Corporation 82801H (ICH8 Family) USB UHCI Controller #3 (rev 02)
00:1d.7 USB controller: Intel Corporation 82801H (ICH8 Family) USB2 EHCI Controller #1 (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev f2)
00:1f.0 ISA bridge: Intel Corporation 82801HM (ICH8M) LPC Interface Controller (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801HM/HEM (ICH8M/ICH8M-E) SATA Controller [IDE mode] (rev 02)
00:1f.3 SMBus: Intel Corporation 82801H (ICH8 Family) SMBus Controller (rev 02)
03:00.0 Ethernet controller: Broadcom Corporation BCM4401-B0 100Base-TX (rev 02)
03:01.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05)
03:01.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22)
03:01.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12)
03:01.3 System peripheral: Ricoh Co Ltd xD-Picture Card Controller (rev 12)
0c:00.0 Network controller: Broadcom Corporation BCM4312 802.11b/g LP-PHY (rev 01)

我知道我需要b43固件集或其他东西，但似乎找不到适合我的说明。

您需要其他任何帮助我的信息，请告诉我，我会尽力提供。

PS：要获取命令的输出，我将命令的输出通过管道传输到USB中的文本文件中，然后从正在运行的计算机中复制粘贴。

编辑1：

输出dmesg | grep -e b43 -e wlan：

[    2.740106] b43-pci-bridge 0000:0c:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    2.740171] b43-pci-bridge 0000:0c:00.0: setting latency timer to 64
[   13.026193] b43-phy0: Broadcom 4312 WLAN found (core revision 15)
[   13.122019] Registered led device: b43-phy0::tx
[   13.122046] Registered led device: b43-phy0::rx
[   13.122069] Registered led device: b43-phy0::radio
[   14.340121] b43-phy0: Loading firmware version 666.2 (2011-02-23 01:15:07)
[   19.988670] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   19.988964] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   23.680660] wlan0: authenticate with 00:26:44:bc:0f:78 (try 1)
[   23.684805] wlan0: authenticated
[   23.685338] wlan0: associate with 00:26:44:bc:0f:78 (try 1)
[   23.692129] wlan0: RX AssocResp from 00:26:44:bc:0f:78 (capab=0x411 status=0 aid=5)
[   23.692135] wlan0: associated
[   23.693238] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   34.660029] wlan0: no IPv6 routers present
[   69.204860] wlan0: deauthenticating from 00:26:44:bc:0f:78 by local choice (reason=3)
[   73.033034] wlan0: authenticate with 00:26:44:bc:0f:78 (try 1)
[   73.034978] wlan0: authenticated
[   73.035362] wlan0: associate with 00:26:44:bc:0f:78 (try 1)
[   73.041193] wlan0: RX ReassocResp from 00:26:44:bc:0f:78 (capab=0x411 status=0 aid=5)
[   73.041198] wlan0: associated
[   84.024051] wlan0: no IPv6 routers present
[  118.208901] wlan0: deauthenticating from 00:26:44:bc:0f:78 by local choice (reason=3)
[  122.305180] wlan0: authenticate with 00:26:44:bc:0f:78 (try 1)
[  122.308896] wlan0: authenticated
[  122.309598] wlan0: associate with 00:26:44:bc:0f:78 (try 1)
[  122.331440] wlan0: RX ReassocResp from 00:26:44:bc:0f:78 (capab=0x411 status=0 aid=5)
[  122.331450] wlan0: associated
[  132.584138] wlan0: no IPv6 routers present
[  168.205906] wlan0: deauthenticating from 00:26:44:bc:0f:78 by local choice (reason=3)
[  172.312791] wlan0: authenticate with 00:26:44:bc:0f:78 (try 1)
[  172.314841] wlan0: authenticated
[  172.315380] wlan0: associate with 00:26:44:bc:0f:78 (try 1)
[  172.320773] wlan0: RX ReassocResp from 00:26:44:bc:0f:78 (capab=0x411 status=0 aid=5)
[  172.320783] wlan0: associated

请将此文件下载到同一USB密钥，然后将其传输到桌面。https://dl.dropboxusercontent.com/u/58267392/b43_new.zip右键单击它，然后选择“在此处提取”。现在，在终端中：

sudo mkdir /lib/firmware/b43
sudo cp Desktop/b43_new/*  /lib/firmware/b43
sudo modprobe -r b43 && sudo modprobe b43

可能需要重新启动。

请查看此问题，因为它可能适用于您的系统-第一个答案建议：

请查看Keryx，它是一个离线存储库管理器。

它是如何工作的？它使您可以将更新和新程序（具有相关性）下载到闪存驱动器。

它的界面类似于突触，但可通过Pendrive进行操作（不需要安装）。不幸的是，GUI需要wxWidgets的，不预装Ubuntu上（他们是跨平台的安装从这里和Ubuntu库在这里）。它只能在Ubuntu系统中安装软件，但是您可以在任何Linux，Windows或OS / X中下载更​​新或新软件包。

在这里可以找到教程。

此答案中的另一个详细的分步教程。

Launchpad还托管可下载的文件。

屏幕截图：